一般耐磨復合鋼板其硬度極高故不適合機械加工，僅能以研磨方式或放電加工進行機械加工，但可適合一般之冷作卷曲加工，為曲率半徑不宜過小以免硬面層剝落，故卷曲加工時請參考產商之建議最小卷曲半徑。卷曲半徑較大時可直接以卷板機彎曲，但卷曲半徑較小時則建議以油壓壓床以圓形刀分多段逐步折彎以避免硬面層剝落。切割時硬面層無法以氧乙炔進行切斷，但可輕易以等離子切割機；雷射(激光)進行切割。由于耐磨板之耐磨壽命極長故若非極為嚴重磨耗之環境可直接于背板焊接方式進行焊接安裝，但焊道處若有磨耗之考慮時宜以硬面焊條保護焊道以免因焊道磨耗導致耐磨板脫落或背板被磨耗而使硬面層剝落。耐磨鋼板若需鉆孔攻牙時則可先以一般鋼材鉆孔攻牙后埋入再于背板焊接而成。
